Search found 1861 matches

Search found 1861 matches Page 1 of 187
by James
Wed May 22, 2019 6:37 am
Forum: Viscosity Support (Mac Version)
Topic: Viscosity 1.7.15 issue with OpenSC
Replies: 1
Views: 47

Hi pethams, Thanks for the report. We've pushed out an updated build of 1.7.15 (build 1488) that resolves the issue. You can automatically update to it immediately by going to Preferences->General and clicking the "Check Now" button. The issue was caused by the OpenSC PKCS#11 library having no code-...
by James
Mon May 20, 2019 8:33 pm
Forum: Viscosity Support (Mac Version)
Topic: Problems with Viscosity/Mojave
Replies: 2
Views: 31

Hi Bowlie, From a Viscosity perspective please ensure that you're using the latest version (version 1.7.14 at the time of writing). You can check this from Viscosity's About section in the Preferences window. Generally the most common cause of problems with Viscosity after upgrading to a major new m...
by James
Thu May 16, 2019 1:57 am
Forum: Viscosity Support (Mac Version)
Topic: Can the service order of Viscosity be adjusted for playing games?
Replies: 1
Views: 28

Hi ironladybugfresh, Setting the DNS Mode to "Full" for the connection should achieve this, however many games identify the primary broadcast interface by the default route (in which case you'll send to have all traffic being routed through the VPN connection). If you haven't already tried it, somet...
by James
Fri Apr 26, 2019 8:03 pm
Forum: Viscosity Support (Mac Version)
Topic: Once a VPN has connected using a particular network card, it cannot connect again unless that network card is active
Replies: 13
Views: 511

Is there perhaps a way to tell Viscosity at connection time that I want to set up some manual routes so that it will properly remove them when it disconnects? The approach you'll want to take if using your own scripts is to log the routes it has created to a text file somewhere, and then upon disco...
by James
Mon Apr 22, 2019 10:32 pm
Forum: Viscosity Support (Mac Version)
Topic: Once a VPN has connected using a particular network card, it cannot connect again unless that network card is active
Replies: 13
Views: 511

Could you give me an example of a valid route-ipv6 line as it would appear in an OVPN profile or in "View Configuration Data"? route-ipv6 2001:abcd::0:1234/64 2001:abcd::1:1234 default The VPN does support IPv6, so I'll need to try something else then. You can essentially disable IPv6 on the VPN co...
by James
Mon Apr 22, 2019 6:49 pm
Forum: Viscosity Support (Mac Version)
Topic: Viscosity vpn connection issue
Replies: 1
Views: 63

Hi backherozzo, The following lines in your log indicates that there is an invalid command in your connection: 2019-04-19 21:47:32: Options error: The command "XXXX" or one of its parameters is invalid for this version of OpenVPN (2.4.6). Please edit the connection, make sure the command is valid, a...
by James
Thu Apr 18, 2019 12:48 pm
Forum: Viscosity Support (Mac Version)
Topic: Once a VPN has connected using a particular network card, it cannot connect again unless that network card is active
Replies: 13
Views: 511

Unfortunately I'm still unable to add an IPv6 route to Viscosity. Each time I create an IPv6 route it doesn't stick -- it just disappears the next time I open the settings window. It sounds like the syntax being used may be invalid, or the IPv6 address/es being entered may be invalid. I recommend t...
by James
Tue Apr 16, 2019 8:05 pm
Forum: Viscosity Support (Mac Version)
Topic: Once a VPN has connected using a particular network card, it cannot connect again unless that network card is active
Replies: 13
Views: 511

Hi bribri,

Sadly net_gateway isn't currently supported for IPv6 routes. We'll likely add support for it in the future, but for now you'll need to manually specify the IPv6 address of the gateway to use (that'll likely be the IPv6 address of your router).

Cheers,
James
by James
Mon Apr 15, 2019 11:59 am
Forum: Viscosity Support (Mac Version)
Topic: Once a VPN has connected using a particular network card, it cannot connect again unless that network card is active
Replies: 13
Views: 511

1. When specifying hostnames that are routed through the local gateway, is it necessary for me to add entries for both IP4 and IP6? Yes, it is. 2. Is there a convenient way I can set up all of my VPN connections to have all the same entries in their routing table without having to manually add them...
by James
Fri Apr 12, 2019 5:12 pm
Forum: Viscosity Support (Mac Version)
Topic: Once a VPN has connected using a particular network card, it cannot connect again unless that network card is active
Replies: 13
Views: 511

Hi bribri, Well what's happening here is that a static route is being created at connection time, routing the server's external IP address through one interface/router, and it doesn't appear to be getting removed at disconnection time. Your config itself looks fine, so it'll have to be one of the fo...
Search found 1861 matches Page 1 of 187